How to mount PVC ?

How to mount PVC ?

Watch the video

How to mount PVC?

installation PVC panels - absolutely simple process for a man who can perform minimal carpentry work, knows how to deal with hand hacksaw and hammer small nails.Before you attach the PVC panels, you must purchase the material, as well as the relevant tools, stock wooden slats.They are necessary for the production of crates on the wall.Depending on how the walls of the room to be fixed panel - with internal or external, rack must buy 30h10 mm or 30x20 mm, respectively.At the final stage of mounting the panels, you will need moldings - finishing strips, which are superimposed on the angular joints of panels (door or window opening).If you want to warm the room, the PVC between the panel and the wall is laid a layer of insulation - Styrofoam plates or loose wood fibers.

Tools for

Quickly and accurately perform the installation of PVC panels allow the following tools:

  • Screwdriver or screwdriver.
  • Plumb and square.
  • small nails or staples with a corro
    sion-resistant coating.
  • Building level which will help to align the batten in different planes.
  • Electric drill, pliers and hammer, dobojnik and metal shears.
  • Hacksaw metal and wood, direct rail and roulette.
  • cord and pencil.

Mounting batten

Before you attach the PVC panels, video review, as a visual aid is always better to talk about the performance of a particular type of work, rather than the text presentation.In any case, you must first work to begin installation batten.Crate - a design that is mounted on the wall using conventional screws or nails, but to carry out this phase of the work must be very carefully and correctly.Do not forget to enjoy the process of the level, so you can punt crate as straight as possible.Thus, imposing wooden slats on the wall, you will level the surface.

attractiveness of using PVC panels is that before starting work, you do not need to conduct any training walls, that is, to peel wallpaper, align the wall with the help of some mixtures, you do not need.Battens screwed to the walls at a distance of 30-40 cm from each other.As battens can use not only the wooden slats, and PVC profile or metal profile.Doing crate, do not forget to apply slats around window and door openings, otherwise, you will not be able to stick around the door opening panel.

Mount PVC panels can be, both in horizontal and vertical, without forgetting that the method of installation depends on the look of the room.If fastening panels provided horizontally, vertically attached lathing, and when the panels are mounted vertically, the crate is superimposed on the wall horizontally.To learn how to correctly attach the PVC panels and lath, said a lot.For its part, will add only that before mounting batten, put its outline with chalk on oblitsuemuyu surface (wall or ceiling).In rooms with high humidity is best to use all the same metal or PVC frame.

Installation

panels Once on your surface, which will be faced with PVC panels, there was a crate, proceed to the next stage of work - wall panels.Starting work should be on the premises of the angle by moving left or right, but remember that there is always a wide panel mounting bracket (if the crate was made of metal profiles) should be placed towards the installation of motion.be sure to refer to those indicators, which shows your level of construction When the installation.

panel is attached to the frame rails through the mounting bracket with the general use of metal staples, small studs, which can be replaced and the screws.The second panel is fully inserted into the groove of the previous panel, and its wide mounting plate is attached to the frame rails as well as you fasten the first panel.All work on the follow-mount panels are performed similarly.

Before you attach the PVC panels, you will need to cut them to length.This process is best done with a saw blade with a small gear.If you must cut across the board, start with the thickened part of the panel.Cut off the panel at the corners must be using the miter box.Then, at angles superimposed moldings.Correctly and accurately completed all installation PVC panels guarantee a perfectly smooth surface of the ceiling and walls, as well as internal or external appeal of the room.